CARRERA
Order the Carrera and receive 4pcs Motor Guards/softmount for free!
Direct conversion kit for Mobula 7 , Pro2 and Trashcan
Whats New:
V3
Widens the arms by a few mm. for added rigidity
Redesigned motor mount for added strenght
Redesigned lipo mount
V2.1
- Redesigned arms/motor mounts
- Now uses Twist and Lock Lipo Mount
V2
- Now includes a self adjusting 2S Lipo mount (350~450)
- More rigid arms
- Redesigned motor mounts for a more aggressive design (see pic)
- Direct conversion kit for Sailfly S and Mobula 7 using the AIO pod
Features:
2mm full carbon fiber main plate.
Designed for the 65mm propellers , flies great too on 56mm props
AIO camera and stack are directly mounted on the TPU pod and not on the CF frame eliminating jellow and gyro issues.
Front hinge pod mount for easy removal and repair
Only 3 screws needed to complete the build (included)
No soldering or cutting needed
Complete the conversion in less than 30min.
Thicker 1.3mm TPU flexible pod
Fully protected camera lens with fixed tilt of 30 or 40 degree angle on EOS pod version and an adjustable tilt on EOS Pod version
FC stack is mounted on the pod and not on the main plate isolating it from vibration (AIO version only)
Fully accessible micro usb port and a access hole for changing the VTX channel
Although it was intended for the 0802 motors it still have a mount for 11xx motors
Easy swap frame and will be offering different design in the future.
Comes with 2 Battery holder for 2x 250mah 1S and 350mah 2S (beta75x)
EOS Pod version comes
Specification:
2mm 3K carbon fiber with cut along the weave
3D Printed flexible TPU pod
Motor mount for the M7 0802 motors
Motor mount for 11xx motors
Included with the kit:
M7 AIO AIO direct Conversion Kit:
1pc. 1.3mm thick TPU pod
1pc. TPU FC stack holder
1pc. CF main plate
1pc. Lipo mount for for 2x 250mah 1s for 2s output
1pc. Lipo mount for 350mah 2s (beta75x)
12pc. M1.4 motor screws
4pcs Motor guards/softmounts NEW
Set of mounting hardware
M7/Trashcan/Pro2 EOS Pod kit.
1pc. 1.3mm thick TPU pod
1pc. Whoop FC stack holder
1pc. VTX holder for the upgraded half stack vtx
1pc. CF main plate
1pc. Lipo mount for for 2x 250mah 1s
1pc. Lipo mount for 350mah 2s (beta75x)
12pc. M1.4 motor screws
Set of Mounting hardware
Recommended Parts:
- Designed to fit all the components from your Mobula7 or:
- Crazybee F4 Whoop size flight controller
- 25mw AIO camera with 14x14 dimension (must have the same size as the M7 aio camera)
- 0802 16000KV motors with jst plug
- 65mm Propellers with 1mm center hole (Brand: Kingkong)
- much better if you upgrade to XT30 lipo plug to reduce sagging
- 300mah 2s lipo similar to the beta75x
- EOS1/2 camera if using the EOS Pod
Build note:
- CLICK HERE : CARRERA BUILD GUIDE
- Because it's a direct conversion kit you will just need to transfer all your electronics to the new frame and you are good to go.
- There are mounting holes to accept 11xx motors but you might need to extend the wires.
- Pinch or squish the pod from top and bottom then insert the AIO camera carefull not to damage the wires.
- Lipo holster is pressure fitted to the CF frame so you will need to squish the lipo mount and isert it on the main plates center hole, use a screw driver to help you pull the mount in place.
- Use a rubberband to hold non standard size lipos
- as tested weight of only 34g without lipo and 47g with 2s lipo
Free to download 3D printed parts:
Carrera Motor Guards /Softmouts
Build Videos:
EOS Version
Flight and Review Videos
BUILD VIDEO
https://www.youtube.com/watch?v=YBcOz4bDqHs&fbclid=IwAR35Odl8xsl4IRO5YwaIhNUYlhHuLk3564FxU7tCP940yb3hppyumh1KKTc
https://www.youtube.com/watch?v=-Bw1Q_zkWDI&feature=youtu.be&fbclid=IwAR2mz2l8sJevslulsCSnHO2nwC8ZQqbYVUS5TCOoeMGYg98dqlHa6vkwYhA
Note: Picture shown are for illustration purposes only. Some parts might not be included with the kit. Please check product description for more details.